Re: [oc] I2C noise filtering

[Richard Herveille <richard@asics.ws>]

You are talking about the i2c slave again right??
Both SCL and SDA are bidirectional signals (inout). So you probably do want to 
use general purpose IOs for SCL and SDA. Unless you do not support clock 
stretching (wait state generation), in that case you can use a global clock 
pin for the SCL line. Although I2C is so slow it shouldn't matter (might ease 
up routing in you FPGA though).

> my clock is 10mhz (xilinx) and both sda and scl is tied to general IO.
>  So, like you said,  I have to output po_scl_cln to another general IO
> and and tie it to Global clk pin?  Is there any way to avoid it
> because it's too difficult to solder such a small and close pin chip.
>  And also, I thought start and stop condition will reset all, but why
> there is another reset for it?  Since I don't have choice for reset on
> the board, will that be an issue?
>
>
>
> Ken
>
> ----- Original Message -----
> From: Illan Glasner <IGlasner@m... >
> To: "'cores@o... '" <cores@o... >
> Date: Wed, 6 Nov 2002 19:14:54 -0800
> Subject: RE: [oc] I2C noise filtering
>
> > Hi,
> >
> >    You can try something like :
> >
> > reg     [2:0]   scnt;
> > always @(posedge pi_clk or negedge rstn)
> > if (~rstn)
> >    scnt <= #1 0;
> > else if (scl)
> >    scnt <= #1 (scnt==7) ? 7 : scnt + 1 ;
> > else
> >    scnt <= #1 (scnt==0) ? 0 : scnt - 1 ;
> >
> > reg     po_scl_cln   ;
> > always @(posedge pi_clk)
> > if (~rstn)
> >    po_scl_cln <= #1 0;
> > else
> >    po_scl_cln <= #1 scnt[2] ;
> >
> >
> > keep in mind that if you use Xilinx you probably will need to send
> > po_scl_cln to a general IO make an external connection on the board
> > to GCLK
> > IO in order to use the clock resource.
> >
> > if you are using altera in this matter it should be easier as you
> > can use
> > directly the po_scl_cln.
> >
> > where pi_clk is a high frequncy clock much faster than the scl
> > something
> > like 10M.
> >
> > if you don;t have high frequnacy you can make another "loop" of
> > geenral IO
> > to GCLK input and simple generate internaly a free runing ring osc
> > using let
> > say 6 buffer and invertor and this should do the job.
> >
> > have a nice day
> >
> >    Illan
> >
> >
> >
> > -----Original Message-----
> > From: ckh827@h...  [mailto:ckh827@h... ]
> > Sent: Wednesday, November 06, 2002 8:01 PM
> > To: cores@o...
> > Subject: [oc] I2C noise filtering
> >
> >
> >
> >
> > When I try to synthesize the I2C verilog from Richard (Opencores),
> > It
> > said unable to open timescale.v. But I already added the source in
> > the
> > project.  Anybody has any idea?
> >
> > And also, how can I filter out the noise from scl and sda lines?
> >
> > I'm urgently need a working I2C slave model because I already
> > worked
> > for more than 3 weeks but still not able to ping correctly.
> >
> > Any help is appreciated.
> >
> > Ken

--
To unsubscribe from cores mailing list please visit http://www.opencores.org/mailinglists.shtml