[SOLVED] easyVDR 3 clean Installation in NUC6i5SYK. Sound and remote problem.

[jb]

Hi.

Till now I had an old installation of easyvdr 3.0 alpha 2 working correctly in my system. Today I updated to easyvdr 3.0 stable, but I have two issues after the first setup (may be I missundertood bad some messages during setup proccess):

- Sound is not working.
- Remote control is not working.

As I have easyinfo with the alpha and with the stable version, I upload them in order you can give some clue about what is working wrong in my new stable version.

Thanks and regards.
Javier B.

[MFG]

Moin moin jb,

do you retried multiple the "SetupTool" via console for audi and lirc?

For audio I found this hint to update freshest alsa - especially for NUC -> may help
And the errors on WIFI in the syslog may be fixed by one of the firmware from here.

MfG.
...........MFG.

[jb]

Hi MFG.

do you retried multiple the "SetupTool" via console for audi and lirc?

I do not know.. may be, Could that be the cause of the issue with sound and remote control? Is there a way to solve the problem that the multiple SetupTool may have caused?

For audio I found this hint to update freshest alsa - especially for NUC -> may help

I thought that as with the alpha2, the audio drivers will be installed by default in the NUC. So, do I have to do this?

Code:

sudo add-apt-repository ppa:ubuntu-audio-dev/alsa-daily.
apt update.
apt install oem-audio-hda-daily-dkms
Reboot the system.

And the errors on WIFI in the syslog may be fixed by one of the firmware from here.

Well, as I have the NUC directly connected to the router I do not need the wifi drivers, so I am not worried about them... unless you tell me that it can affect to the system performance.

The remote control control is not working in this installation, but it works in the Alpha2 version, do I need also some aditional drivers?

Thanks and regards.
Javier B.

[MFG]

Moin moin jb,

do you know, howto enter the Setup via ToolMenu to configure again?

On VDR: [CTRL][ALT][F3] --- LogIn --- easyvdr / easyvdr then choose "VDR-Setup" and e.g. Audio...
Via Putty: LogIn --- easyvdr / easyvdr then choose "VDR-Setup" and e.g. Audio...

MfG.
............MFG.

[jb]

do you know, howto enter the Setup via ToolMenu to configure again?

On VDR: [CTRL][ALT][F3] --- LogIn --- easyvdr / easyvdr then choose "VDR-Setup" and e.g. Audio...
Via Putty: LogIn --- easyvdr / easyvdr then choose "VDR-Setup" and e.g. Audio...

I am sorry, do you mean in the script launched automatically after an ssh conection?

I try to enter VDR-Setup, and I receive this message:

Code:

Sie haben keine Adminrechte. Bitte erst das Passwort eingeben und dann nochmal

Google translator tells me that:

Code:

You have no admin rights. Please enter the password first and then again

But I do not know what to do  . I had had entered the password when I connected.

May be it is obvious, but I am sorry, not for me. How can I enter there?

Regards.
Javier B.

[Oberlooser]

First Ctrl,alt and F2
Login:easyvdr
Passwort:easyvdr
Then Administrator Terminal
Passwort:easyvdr and then use the Setup

Oberlooser

[MFG]

Moin moin jb,

do you know, howto enter the Setup via ToolMenu to configure again?

On VDR: [CTRL][ALT][F3] --- LogIn --- easyvdr / easyvdr then choose "VDR-Setup" and e.g. Audio...
Via Putty: LogIn --- easyvdr / easyvdr then choose "VDR-Setup" and e.g. Audio...

I am sorry, do you mean in the script launched automatically after an ssh conection?

I try to enter VDR-Setup, and I receive this message:

Code:

Sie haben keine Adminrechte. Bitte erst das Passwort eingeben und dann nochmal

Google translator tells me that:

Code:

You have no admin rights. Please enter the password first and then again

But I do not know what to do   . I had had entered the password when I connected.

Jes Sir, that is right Point ;-]

At the ToolMenu what you see after ssh/putty/Console-Login:
at the bottom choose "Admin werden" and enter the password "easyvdr"
after this choose "VDR-Setup"
here you can restart/reconfigure all steps of the setup.

MfG.
...........MFG.

[jb]

Hi. Thanks for the help but...

I entered in the audio setup and I obtained the msg01.jpg and msg01.jpg that I have uploaded.

Tv screen got black with a message, but no sound is played (I remember that when I installed alpha2 tv played diferent sounds).

I am sorry for the inconvenience, I am not able to find out where to change the sound output.

I tried to configure also the remote control with the setup but with no luck neither.

I do not know what exactly to ask you more or what info can I give you.

Regards.
Javier B.

[jb]

Hi again.

I entered in the option experimental/pulse audio and it seems that I achieved get the sound working.

Thanks for your help.

Now I would need to reconfigure remote control to work. In alpha2 I had a Microsoft MCE configured. What can I do to check what is the problem with the remote?

Regards.
Javier B.

[Oberlooser]

Hi Javier
You must Login in the vdr-setup
go to Fernbedienung and check what is your Receiver (Fb-Receiver)
after this go to Fernbedienung and take your Fernbedienung MS_MCE or
your Model .
At last reboot your VDR new.
Greetz
Oberlooser

[jb]

Hi Javier
You must Login in the vdr-setup
go to Fernbedienung and check what is your Receiver (Fb-Receiver)
after this go to Fernbedienung and take your Fernbedienung MS_MCE or
your Model .
At last reboot your VDR new.
Greetz
Oberlooser

Hi Oberlooser.

I did that this morning but it seems not to work.

Something that can be checked by other way?

Regards
Javier B

[Oberlooser]

Hi
Can you show me your Model of Receiver or name of the Modell
and the Modell of your Remote.
Work your Keyboard ootb
Is in the BIO,s of your Mainboard the Port of your Receiver aktivated,
USB or COM Port.   Com1, Com2 or Auto Mode
Greetz
Oberlooser

[jb]

Hi
Can you show me your Model of Receiver or name of the Modell
and the Modell of your Remote.
Work your Keyboard ootb
Is in the BIO,s of your Mainboard the Port of your Receiver aktivated,
USB or COM Port.   Com1,  Com2 or Auto Mode
Greetz
Oberlooser

Hi

I have installed the alpha2 version in a ssd hard disk and the stable version in another, I do not think the problem is about the BIOS because the remote works fine in the same NUC with de ssd of the alpha2 version and it do not work with the ssd of the stable version.

In the webportal the CIR Receiver is ITE8713_CIReceiver and the remote MS_MCE (is an One for all, configured as MS MCE). I guess it can be checked in the two easyInfo of the first post (one for each version of easyVdr).

The keyboard works fine and I can change the channels or move over the OSD.

Regards.
Javier B.

[jb]

Hi again.

I have done another time the changes that Overlooser told me. You can see the two images uploaded on this post, but with no luck again.

I upload also on this post the list of packages installed in alpha2 version and in Stable version, just in case that can give some idea about some CIR package that is missing in my Stable installation.

When I run this command:

Code:

cat /proc/bus/input/devices

I obtain in Apha2 version those results:

Code:

I: Bus=0019 Vendor=0000 Product=0003 Version=0000
N: Name="Sleep Button"
P: Phys=PNP0C0E/button/input0
S: Sysfs=/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input0
U: Uniq=
H: Handlers=kbd event0
B: PROP=0
B: EV=3
B: KEY=4000 0 0

I: Bus=0019 Vendor=0000 Product=0001 Version=0000
N: Name="Power Button"
P: Phys=PNP0C0C/button/input0
S: Sysfs=/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input1
U: Uniq=
H: Handlers=kbd event1
B: PROP=0
B: EV=3
B: KEY=10000000000000 0

I: Bus=0019 Vendor=0000 Product=0001 Version=0000
N: Name="Power Button"
P: Phys=LNXPWRBN/button/input0
S: Sysfs=/devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
U: Uniq=
H: Handlers=kbd event2
B: PROP=0
B: EV=3
B: KEY=10000000000000 0

I: Bus=0019 Vendor=1283 Product=0000 Version=0000
N: Name="ITE8713 CIR transceiver"
P: Phys=
S: Sysfs=/devices/virtual/rc/rc0/input3
U: Uniq=
H: Handlers=kbd event3
B: PROP=0
B: EV=100013
B: KEY=fff 0 108fc326 217604100000000 0 118000 418000000801 9e968000000000 10000000
B: MSC=10

I: Bus=0000 Vendor=0000 Product=0000 Version=0000
N: Name="MCE IR Keyboard/Mouse (ite-cir)"
P: Phys=/input0
S: Sysfs=/devices/virtual/input/input4
U: Uniq=
H: Handlers=sysrq kbd mouse0 event4
B: PROP=0
B: EV=100017
B: KEY=30000 7 ff87207ac14057ff febeffdfffefffff fffffffffffffffe
B: REL=3
B: MSC=10

I: Bus=0003 Vendor=046d Product=404d Version=0111
N: Name="Logitech K400 Plus"
P: Phys=usb-0000:00:14.0-4:1
S: Sysfs=/devices/pci0000:00/0000:00:14.0/usb1/1-4/1-4:1.2/0003:046D:C52B.0003/0003:046D:404D.0004/input/input5
U: Uniq=
H: Handlers=sysrq kbd mouse1 event5
B: PROP=0
B: EV=12001f
B: KEY=3007f 0 0 483ffff17aff32d bf54444600000000 ffff0001 130f938b17c007 ffff7bfad941dfff febeffdfffefffff fffffffffffffffe
B: REL=1c3
B: ABS=100000000
B: MSC=10
B: LED=1f

I: Bus=0019 Vendor=0000 Product=0006 Version=0000
N: Name="Video Bus"
P: Phys=LNXVIDEO/video/input0
S: Sysfs=/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input6
U: Uniq=
H: Handlers=kbd event6
B: PROP=0
B: EV=3
B: KEY=3e000b00000000 0 0 0

I: Bus=0000 Vendor=0000 Product=0000 Version=0000
N: Name="HDA Intel PCH Mic"
P: Phys=ALSA
S: Sysfs=/devices/pci0000:00/0000:00:1f.3/sound/card0/input7
U: Uniq=
H: Handlers=event7
B: PROP=0
B: EV=21
B: SW=10

I: Bus=0000 Vendor=0000 Product=0000 Version=0000
N: Name="HDA Intel PCH Headphone"
P: Phys=ALSA
S: Sysfs=/devices/pci0000:00/0000:00:1f.3/sound/card0/input8
U: Uniq=
H: Handlers=event8
B: PROP=0
B: EV=21
B: SW=4

I: Bus=0000 Vendor=0000 Product=0000 Version=0000
N: Name="HDA Intel PCH HDMI/DP,pcm=3"
P: Phys=ALSA
S: Sysfs=/devices/pci0000:00/0000:00:1f.3/sound/card0/input9
U: Uniq=
H: Handlers=event9
B: PROP=0
B: EV=21
B: SW=140

I: Bus=0000 Vendor=0000 Product=0000 Version=0000
N: Name="HDA Intel PCH HDMI/DP,pcm=7"
P: Phys=ALSA
S: Sysfs=/devices/pci0000:00/0000:00:1f.3/sound/card0/input10
U: Uniq=
H: Handlers=event10
B: PROP=0
B: EV=21
B: SW=140

I: Bus=0000 Vendor=0000 Product=0000 Version=0000
N: Name="HDA Intel PCH HDMI/DP,pcm=8"
P: Phys=ALSA
S: Sysfs=/devices/pci0000:00/0000:00:1f.3/sound/card0/input11
U: Uniq=
H: Handlers=event11
B: PROP=0
B: EV=21
B: SW=140

I: Bus=0003 Vendor=2304 Product=0237 Version=0100
N: Name="IR-receiver inside an USB DVB receiver"
P: Phys=usb-0000:00:14.0-1.1/ir0
S: Sysfs=/devices/pci0000:00/0000:00:14.0/usb1/1-1/1-1.1/rc/rc1/input12
U: Uniq=
H: Handlers=kbd event12
B: PROP=0
B: EV=100013
B: KEY=14afc336 284284d00000000 0 480058000 219040000801 9e96c000000000 90020000000ffc
B: MSC=10

I: Bus=0003 Vendor=2304 Product=0237 Version=0100
N: Name="IR-receiver inside an USB DVB receiver"
P: Phys=usb-0000:00:14.0-1.2/ir0
S: Sysfs=/devices/pci0000:00/0000:00:14.0/usb1/1-1/1-1.2/rc/rc2/input13
U: Uniq=
H: Handlers=kbd event13
B: PROP=0
B: EV=100013
B: KEY=14afc336 284284d00000000 0 480058000 219040000801 9e96c000000000 90020000000ffc
B: MSC=10

I: Bus=0003 Vendor=2304 Product=0237 Version=0100
N: Name="IR-receiver inside an USB DVB receiver"
P: Phys=usb-0000:00:14.0-1.3/ir0
S: Sysfs=/devices/pci0000:00/0000:00:14.0/usb1/1-1/1-1.3/rc/rc3/input14
U: Uniq=
H: Handlers=kbd event14
B: PROP=0
B: EV=100013
B: KEY=14afc336 284284d00000000 0 480058000 219040000801 9e96c000000000 90020000000ffc
B: MSC=10

and I obtain in Stable version those results:

Code:

I: Bus=0019 Vendor=0000 Product=0003 Version=0000
N: Name="Sleep Button"
P: Phys=PNP0C0E/button/input0
S: Sysfs=/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input0
U: Uniq=
H: Handlers=kbd event0
B: PROP=0
B: EV=3
B: KEY=4000 0 0

I: Bus=0019 Vendor=0000 Product=0001 Version=0000
N: Name="Power Button"
P: Phys=PNP0C0C/button/input0
S: Sysfs=/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input1
U: Uniq=
H: Handlers=kbd event1
B: PROP=0
B: EV=3
B: KEY=10000000000000 0

I: Bus=0019 Vendor=0000 Product=0001 Version=0000
N: Name="Power Button"
P: Phys=LNXPWRBN/button/input0
S: Sysfs=/devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
U: Uniq=
H: Handlers=kbd event2
B: PROP=0
B: EV=3
B: KEY=10000000000000 0

I: Bus=0019 Vendor=1283 Product=0000 Version=0000
N: Name="ITE8713 CIR transceiver"
P: Phys=
S: Sysfs=/devices/virtual/rc/rc0/input3
U: Uniq=
H: Handlers=kbd event3
B: PROP=0
B: EV=100013
B: KEY=fff 0 108fc326 217604100000000 0 118000 418000000801 9e968000000000 10000000
B: MSC=10

I: Bus=0000 Vendor=0000 Product=0000 Version=0000
N: Name="MCE IR Keyboard/Mouse (ite-cir)"
P: Phys=/input0
S: Sysfs=/devices/virtual/input/input4
U: Uniq=
H: Handlers=sysrq kbd mouse0 event4
B: PROP=0
B: EV=100017
B: KEY=30000 7 ff87207ac14057ff febeffdfffefffff fffffffffffffffe
B: REL=3
B: MSC=10

I: Bus=0003 Vendor=046d Product=404d Version=0111
N: Name="Logitech K400 Plus"
P: Phys=usb-0000:00:14.0-4:1
S: Sysfs=/devices/pci0000:00/0000:00:14.0/usb1/1-4/1-4:1.2/0003:046D:C52B.0003/0003:046D:404D.0004/input/input5
U: Uniq=
H: Handlers=sysrq kbd mouse1 event5 leds
B: PROP=0
B: EV=12001f
B: KEY=3007f 0 0 483ffff17aff32d bf54444600000000 ffff0001 130f938b17c007 ffff7bfad941dfff febeffdfffefffff fffffffffffffffe
B: REL=1c3
B: ABS=100000000
B: MSC=10
B: LED=1f

I: Bus=0019 Vendor=0000 Product=0006 Version=0000
N: Name="Video Bus"
P: Phys=LNXVIDEO/video/input0
S: Sysfs=/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input6
U: Uniq=
H: Handlers=kbd event6
B: PROP=0
B: EV=3
B: KEY=3e000b00000000 0 0 0

I: Bus=0000 Vendor=0000 Product=0000 Version=0000
N: Name="HDA Intel PCH Mic"
P: Phys=ALSA
S: Sysfs=/devices/pci0000:00/0000:00:1f.3/sound/card0/input7
U: Uniq=
H: Handlers=event7
B: PROP=0
B: EV=21
B: SW=10

I: Bus=0000 Vendor=0000 Product=0000 Version=0000
N: Name="HDA Intel PCH Headphone"
P: Phys=ALSA
S: Sysfs=/devices/pci0000:00/0000:00:1f.3/sound/card0/input8
U: Uniq=
H: Handlers=event8
B: PROP=0
B: EV=21
B: SW=4

I: Bus=0000 Vendor=0000 Product=0000 Version=0000
N: Name="HDA Intel PCH HDMI/DP,pcm=3"
P: Phys=ALSA
S: Sysfs=/devices/pci0000:00/0000:00:1f.3/sound/card0/input9
U: Uniq=
H: Handlers=event9
B: PROP=0
B: EV=21
B: SW=140

I: Bus=0000 Vendor=0000 Product=0000 Version=0000
N: Name="HDA Intel PCH HDMI/DP,pcm=7"
P: Phys=ALSA
S: Sysfs=/devices/pci0000:00/0000:00:1f.3/sound/card0/input10
U: Uniq=
H: Handlers=event10
B: PROP=0
B: EV=21
B: SW=140

I: Bus=0000 Vendor=0000 Product=0000 Version=0000
N: Name="HDA Intel PCH HDMI/DP,pcm=8"
P: Phys=ALSA
S: Sysfs=/devices/pci0000:00/0000:00:1f.3/sound/card0/input11
U: Uniq=
H: Handlers=event11
B: PROP=0
B: EV=21
B: SW=140

I: Bus=0003 Vendor=2304 Product=0237 Version=0100
N: Name="IR-receiver inside an USB DVB receiver"
P: Phys=usb-0000:00:14.0-1.1/ir0
S: Sysfs=/devices/pci0000:00/0000:00:14.0/usb1/1-1/1-1.1/rc/rc1/input12
U: Uniq=
H: Handlers=kbd event12
B: PROP=0
B: EV=100013
B: KEY=14afc336 284284d00000000 0 480058000 219040000801 9e96c000000000 90020000000ffc
B: MSC=10

I: Bus=0003 Vendor=2304 Product=0237 Version=0100
N: Name="IR-receiver inside an USB DVB receiver"
P: Phys=usb-0000:00:14.0-1.2/ir0
S: Sysfs=/devices/pci0000:00/0000:00:14.0/usb1/1-1/1-1.2/rc/rc2/input13
U: Uniq=
H: Handlers=kbd event13
B: PROP=0
B: EV=100013
B: KEY=14afc336 284284d00000000 0 480058000 219040000801 9e96c000000000 90020000000ffc
B: MSC=10

I: Bus=0003 Vendor=2304 Product=0237 Version=0100
N: Name="IR-receiver inside an USB DVB receiver"
P: Phys=usb-0000:00:14.0-1.3/ir0
S: Sysfs=/devices/pci0000:00/0000:00:14.0/usb1/1-1/1-1.3/rc/rc3/input14
U: Uniq=
H: Handlers=kbd event14
B: PROP=0
B: EV=100013
B: KEY=14afc336 284284d00000000 0 480058000 219040000801 9e96c000000000 90020000000ffc
B: MSC=10

Running this command in boht versions:

Code:

sudo ir-keytable -t --device=/dev/input/event3

Any of them detects the key pressing on the remote.

I have checked some pages about infrared configuration in ubuntu on internet but that is hard information to me for understanding it.

I am sorry, If I can give you more info or run more test, just ask for it.

In the meantime, till the problem with the remote/CIR receiver is solved, I let installed the ssd hard disk with the alpha2 version in order we can use easyVdr at home.

Regards.
Javier B.

[Oberlooser]

Hi Javier
What happens when you take the remote.conf and lircd.conf from the ssd
From your old installation 2.5

Is worth a try
Greetz Oberlooser

[jb]

What happens when you take the remote.conf and lircd.conf from the ssd
From your old installation 2.5

Hi Oberlooser.

I think I do not understand you.
You mean if I remove remote.conf and lircd.conf in the installation of easyvdr 3 Alpha2? What happens if I try to use the remote?
or you propose to copy those files to the installation of easyvdr 3 Stable?

[Edited: I have compared the files in both versions with the easyvdrInfo files and in Alpha2 and in the Stable version the files are equal]]



Regards.
Javier B.

[Oberlooser]

Yes if the files are the same
I can not help you
Could be that they are different
I do not know any more
greeting
Oberlooser

[jb]

Well. Thanks a lot anyway.

It seems that is happening the same issue that when I tried to test the Alpha4 version... see this thread: http://www.easy-vdr.de/thread-17447.html

There, michel8 tried to helpme, but I decided to wait till the Stable version, so, we did not keep on solving the issue.

The last info demanded in that thread by michel8 was:

could you please post the content of
   /lib/udev/rules.d/40-ir-keytable.rules
the output of
   ir-keytable -v
and the content of
  /var/log/easyvdr/easyvdr-set_keytab
In the Logfile I have seen, that you are using an MCE-CIR Keyboard/Mouse, Did you also had this component in use with your last successfull remote-control configuration with Alpha 2-ISO?

Do you think that can be useful if I find out this info for the version that is working (V3 Alpha2) and for the version that is not working (V3 Stable)
in order to compare it?

May be I can check if the sofware that should be running to make work the remote is trully working? If someone could tellme which command should I use?


Regards.
Javier B.

[Oberlooser]

Hi
What happens when you enter irw on the console and press some keys on the remote control
Is something displayed.
So you can see if the remote control sends anything and something is important.
Greetz
Helmut

[gb]

Hi

Hi
What happens when you enter irw on the console and press some keys on the remote control
Is something displayed.

Important:
vdr must run
Then test with irw

greetings Aaron

[jb]

What happens when you enter irw on the console and press some keys on the remote control
Is something displayed.

Moin moin Overlooser

With the alpha2 with irw when I press a key in the remote, the pressed key is displayed on de ssh window and.... when I have changed the hard disk with the Stable version, the first start ... magically   ... the remote worked and irw displayed also the pressed keys... but... after that I have rebooted twice or three times to test again with irw, in all of those times, irw had no response   .

How can be it possible? Sometimes works (only one) and many times do not work.

Does this behaviour give any clue to you? I am perplexed.

Regards.
Javier B.

[Edited: I have tried many more times (7-8), but in any of them irw had any response to the key pressed on the remote]
[Edited a second time: I upload syslog since the first start when remote worked till the second reboot where remote did not work anymore in order you can see if there are something wrong or different in the logs]

[Bleifuss2]

Hallo Javier

What is the output from this command?

Code:

ls -l /dev/input/by-path/*

greetings

Bleifuss

[jb]

What is the output from this command?

Code:

ls -l /dev/input/by-path/*

Hi Bleifuss2.

I run the command in the version alpha2, where remote works fine, and in the Stable version. I have had luck and in one of my tries the remote has been working in the stable version, so I give you the output with the Stable version with remote working and without working:

Code:

In v3 Stable (where remote does not work):

[email protected]:~$ ls -l /dev/input/by-path/*
lrwxrwxrwx 1 root root 10 Nov 17 16:06 /dev/input/by-path/pci-0000:00:14.0-usb-0:1.1-event-ir -> ../event12
lrwxrwxrwx 1 root root 10 Nov 17 16:06 /dev/input/by-path/pci-0000:00:14.0-usb-0:1.2-event-ir -> ../event13
lrwxrwxrwx 1 root root 10 Nov 17 16:06 /dev/input/by-path/pci-0000:00:14.0-usb-0:1.3-event-ir -> ../event14
lrwxrwxrwx 1 root root  9 Nov 17 16:06 /dev/input/by-path/pci-0000:00:14.0-usb-0:4:1.2-event-mouse -> ../event6
lrwxrwxrwx 1 root root  9 Nov 17 16:06 /dev/input/by-path/pci-0000:00:14.0-usb-0:4:1.2-mouse -> ../mouse1
-----------------------------------------------------------------------------------------------------------------------------
In v3 Stable (this time exceptionally remote is working):

[email protected]:~$ ls -l /dev/input/by-path/*
lrwxrwxrwx 1 root root 10 Nov 17 16:01 /dev/input/by-path/pci-0000:00:14.0-usb-0:1.1-event-ir -> ../event12
lrwxrwxrwx 1 root root 10 Nov 17 16:01 /dev/input/by-path/pci-0000:00:14.0-usb-0:1.2-event-ir -> ../event13
lrwxrwxrwx 1 root root 10 Nov 17 16:01 /dev/input/by-path/pci-0000:00:14.0-usb-0:1.3-event-ir -> ../event14
lrwxrwxrwx 1 root root  9 Nov 17 16:01 /dev/input/by-path/pci-0000:00:14.0-usb-0:4:1.2-event-mouse -> ../event5
lrwxrwxrwx 1 root root  9 Nov 17 16:01 /dev/input/by-path/pci-0000:00:14.0-usb-0:4:1.2-mouse -> ../mouse1
-----------------------------------------------------------------------------------------------------------------------------
In v3 Alpha2 (where remote works):
[email protected]:~$ ls -l /dev/input/by-path/*
lrwxrwxrwx 1 root root 10 nov 17 16:15 /dev/input/by-path/pci-0000:00:14.0-usb-0:1.1-event-ir -> ../event12
lrwxrwxrwx 1 root root 10 nov 17 16:15 /dev/input/by-path/pci-0000:00:14.0-usb-0:1.2-event-ir -> ../event13
lrwxrwxrwx 1 root root 10 nov 17 16:15 /dev/input/by-path/pci-0000:00:14.0-usb-0:1.3-event-ir -> ../event14
lrwxrwxrwx 1 root root  9 nov 17 16:15 /dev/input/by-path/pci-0000:00:14.0-usb-0:4:1.2-event-mouse -> ../event5
lrwxrwxrwx 1 root root  9 nov 17 16:15 /dev/input/by-path/pci-0000:00:14.0-usb-0:4:1.2-mouse -> ../mouse1

Regards.
Javier B.

[Bleifuss2]

OK

And what's the output from

cat /proc/bus/input/devices

if the remote is dead, try restart lirc.

Code:

sudo stop lircd
sudo start lircd

[jb]

And what's the output from

cat /proc/bus/input/devices

Hi, the output is posted in a previous post, I copy it again:

When I run this command:

Code:

cat /proc/bus/input/devices

I obtain in Apha2 version (remote works fine) those results:

Code:

I: Bus=0019 Vendor=0000 Product=0003 Version=0000
N: Name="Sleep Button"
P: Phys=PNP0C0E/button/input0
S: Sysfs=/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input0
U: Uniq=
H: Handlers=kbd event0
B: PROP=0
B: EV=3
B: KEY=4000 0 0

I: Bus=0019 Vendor=0000 Product=0001 Version=0000
N: Name="Power Button"
P: Phys=PNP0C0C/button/input0
S: Sysfs=/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input1
U: Uniq=
H: Handlers=kbd event1
B: PROP=0
B: EV=3
B: KEY=10000000000000 0

I: Bus=0019 Vendor=0000 Product=0001 Version=0000
N: Name="Power Button"
P: Phys=LNXPWRBN/button/input0
S: Sysfs=/devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
U: Uniq=
H: Handlers=kbd event2
B: PROP=0
B: EV=3
B: KEY=10000000000000 0

I: Bus=0019 Vendor=1283 Product=0000 Version=0000
N: Name="ITE8713 CIR transceiver"
P: Phys=
S: Sysfs=/devices/virtual/rc/rc0/input3
U: Uniq=
H: Handlers=kbd event3
B: PROP=0
B: EV=100013
B: KEY=fff 0 108fc326 217604100000000 0 118000 418000000801 9e968000000000 10000000
B: MSC=10

I: Bus=0000 Vendor=0000 Product=0000 Version=0000
N: Name="MCE IR Keyboard/Mouse (ite-cir)"
P: Phys=/input0
S: Sysfs=/devices/virtual/input/input4
U: Uniq=
H: Handlers=sysrq kbd mouse0 event4
B: PROP=0
B: EV=100017
B: KEY=30000 7 ff87207ac14057ff febeffdfffefffff fffffffffffffffe
B: REL=3
B: MSC=10

I: Bus=0003 Vendor=046d Product=404d Version=0111
N: Name="Logitech K400 Plus"
P: Phys=usb-0000:00:14.0-4:1
S: Sysfs=/devices/pci0000:00/0000:00:14.0/usb1/1-4/1-4:1.2/0003:046D:C52B.0003/0003:046D:404D.0004/input/input5
U: Uniq=
H: Handlers=sysrq kbd mouse1 event5
B: PROP=0
B: EV=12001f
B: KEY=3007f 0 0 483ffff17aff32d bf54444600000000 ffff0001 130f938b17c007 ffff7bfad941dfff febeffdfffefffff fffffffffffffffe
B: REL=1c3
B: ABS=100000000
B: MSC=10
B: LED=1f

I: Bus=0019 Vendor=0000 Product=0006 Version=0000
N: Name="Video Bus"
P: Phys=LNXVIDEO/video/input0
S: Sysfs=/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input6
U: Uniq=
H: Handlers=kbd event6
B: PROP=0
B: EV=3
B: KEY=3e000b00000000 0 0 0

I: Bus=0000 Vendor=0000 Product=0000 Version=0000
N: Name="HDA Intel PCH Mic"
P: Phys=ALSA
S: Sysfs=/devices/pci0000:00/0000:00:1f.3/sound/card0/input7
U: Uniq=
H: Handlers=event7
B: PROP=0
B: EV=21
B: SW=10

I: Bus=0000 Vendor=0000 Product=0000 Version=0000
N: Name="HDA Intel PCH Headphone"
P: Phys=ALSA
S: Sysfs=/devices/pci0000:00/0000:00:1f.3/sound/card0/input8
U: Uniq=
H: Handlers=event8
B: PROP=0
B: EV=21
B: SW=4

I: Bus=0000 Vendor=0000 Product=0000 Version=0000
N: Name="HDA Intel PCH HDMI/DP,pcm=3"
P: Phys=ALSA
S: Sysfs=/devices/pci0000:00/0000:00:1f.3/sound/card0/input9
U: Uniq=
H: Handlers=event9
B: PROP=0
B: EV=21
B: SW=140

I: Bus=0000 Vendor=0000 Product=0000 Version=0000
N: Name="HDA Intel PCH HDMI/DP,pcm=7"
P: Phys=ALSA
S: Sysfs=/devices/pci0000:00/0000:00:1f.3/sound/card0/input10
U: Uniq=
H: Handlers=event10
B: PROP=0
B: EV=21
B: SW=140

I: Bus=0000 Vendor=0000 Product=0000 Version=0000
N: Name="HDA Intel PCH HDMI/DP,pcm=8"
P: Phys=ALSA
S: Sysfs=/devices/pci0000:00/0000:00:1f.3/sound/card0/input11
U: Uniq=
H: Handlers=event11
B: PROP=0
B: EV=21
B: SW=140

I: Bus=0003 Vendor=2304 Product=0237 Version=0100
N: Name="IR-receiver inside an USB DVB receiver"
P: Phys=usb-0000:00:14.0-1.1/ir0
S: Sysfs=/devices/pci0000:00/0000:00:14.0/usb1/1-1/1-1.1/rc/rc1/input12
U: Uniq=
H: Handlers=kbd event12
B: PROP=0
B: EV=100013
B: KEY=14afc336 284284d00000000 0 480058000 219040000801 9e96c000000000 90020000000ffc
B: MSC=10

I: Bus=0003 Vendor=2304 Product=0237 Version=0100
N: Name="IR-receiver inside an USB DVB receiver"
P: Phys=usb-0000:00:14.0-1.2/ir0
S: Sysfs=/devices/pci0000:00/0000:00:14.0/usb1/1-1/1-1.2/rc/rc2/input13
U: Uniq=
H: Handlers=kbd event13
B: PROP=0
B: EV=100013
B: KEY=14afc336 284284d00000000 0 480058000 219040000801 9e96c000000000 90020000000ffc
B: MSC=10

I: Bus=0003 Vendor=2304 Product=0237 Version=0100
N: Name="IR-receiver inside an USB DVB receiver"
P: Phys=usb-0000:00:14.0-1.3/ir0
S: Sysfs=/devices/pci0000:00/0000:00:14.0/usb1/1-1/1-1.3/rc/rc3/input14
U: Uniq=
H: Handlers=kbd event14
B: PROP=0
B: EV=100013
B: KEY=14afc336 284284d00000000 0 480058000 219040000801 9e96c000000000 90020000000ffc
B: MSC=10

and I obtain in Stable version (remote does not work most of times) those results:

Code:

I: Bus=0019 Vendor=0000 Product=0003 Version=0000
N: Name="Sleep Button"
P: Phys=PNP0C0E/button/input0
S: Sysfs=/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input0
U: Uniq=
H: Handlers=kbd event0
B: PROP=0
B: EV=3
B: KEY=4000 0 0

I: Bus=0019 Vendor=0000 Product=0001 Version=0000
N: Name="Power Button"
P: Phys=PNP0C0C/button/input0
S: Sysfs=/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input1
U: Uniq=
H: Handlers=kbd event1
B: PROP=0
B: EV=3
B: KEY=10000000000000 0

I: Bus=0019 Vendor=0000 Product=0001 Version=0000
N: Name="Power Button"
P: Phys=LNXPWRBN/button/input0
S: Sysfs=/devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
U: Uniq=
H: Handlers=kbd event2
B: PROP=0
B: EV=3
B: KEY=10000000000000 0

I: Bus=0019 Vendor=1283 Product=0000 Version=0000
N: Name="ITE8713 CIR transceiver"
P: Phys=
S: Sysfs=/devices/virtual/rc/rc0/input3
U: Uniq=
H: Handlers=kbd event3
B: PROP=0
B: EV=100013
B: KEY=fff 0 108fc326 217604100000000 0 118000 418000000801 9e968000000000 10000000
B: MSC=10

I: Bus=0000 Vendor=0000 Product=0000 Version=0000
N: Name="MCE IR Keyboard/Mouse (ite-cir)"
P: Phys=/input0
S: Sysfs=/devices/virtual/input/input4
U: Uniq=
H: Handlers=sysrq kbd mouse0 event4
B: PROP=0
B: EV=100017
B: KEY=30000 7 ff87207ac14057ff febeffdfffefffff fffffffffffffffe
B: REL=3
B: MSC=10

I: Bus=0003 Vendor=046d Product=404d Version=0111
N: Name="Logitech K400 Plus"
P: Phys=usb-0000:00:14.0-4:1
S: Sysfs=/devices/pci0000:00/0000:00:14.0/usb1/1-4/1-4:1.2/0003:046D:C52B.0003/0003:046D:404D.0004/input/input5
U: Uniq=
H: Handlers=sysrq kbd mouse1 event5 leds
B: PROP=0
B: EV=12001f
B: KEY=3007f 0 0 483ffff17aff32d bf54444600000000 ffff0001 130f938b17c007 ffff7bfad941dfff febeffdfffefffff fffffffffffffffe
B: REL=1c3
B: ABS=100000000
B: MSC=10
B: LED=1f

I: Bus=0019 Vendor=0000 Product=0006 Version=0000
N: Name="Video Bus"
P: Phys=LNXVIDEO/video/input0
S: Sysfs=/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input6
U: Uniq=
H: Handlers=kbd event6
B: PROP=0
B: EV=3
B: KEY=3e000b00000000 0 0 0

I: Bus=0000 Vendor=0000 Product=0000 Version=0000
N: Name="HDA Intel PCH Mic"
P: Phys=ALSA
S: Sysfs=/devices/pci0000:00/0000:00:1f.3/sound/card0/input7
U: Uniq=
H: Handlers=event7
B: PROP=0
B: EV=21
B: SW=10

I: Bus=0000 Vendor=0000 Product=0000 Version=0000
N: Name="HDA Intel PCH Headphone"
P: Phys=ALSA
S: Sysfs=/devices/pci0000:00/0000:00:1f.3/sound/card0/input8
U: Uniq=
H: Handlers=event8
B: PROP=0
B: EV=21
B: SW=4

I: Bus=0000 Vendor=0000 Product=0000 Version=0000
N: Name="HDA Intel PCH HDMI/DP,pcm=3"
P: Phys=ALSA
S: Sysfs=/devices/pci0000:00/0000:00:1f.3/sound/card0/input9
U: Uniq=
H: Handlers=event9
B: PROP=0
B: EV=21
B: SW=140

I: Bus=0000 Vendor=0000 Product=0000 Version=0000
N: Name="HDA Intel PCH HDMI/DP,pcm=7"
P: Phys=ALSA
S: Sysfs=/devices/pci0000:00/0000:00:1f.3/sound/card0/input10
U: Uniq=
H: Handlers=event10
B: PROP=0
B: EV=21
B: SW=140

I: Bus=0000 Vendor=0000 Product=0000 Version=0000
N: Name="HDA Intel PCH HDMI/DP,pcm=8"
P: Phys=ALSA
S: Sysfs=/devices/pci0000:00/0000:00:1f.3/sound/card0/input11
U: Uniq=
H: Handlers=event11
B: PROP=0
B: EV=21
B: SW=140

I: Bus=0003 Vendor=2304 Product=0237 Version=0100
N: Name="IR-receiver inside an USB DVB receiver"
P: Phys=usb-0000:00:14.0-1.1/ir0
S: Sysfs=/devices/pci0000:00/0000:00:14.0/usb1/1-1/1-1.1/rc/rc1/input12
U: Uniq=
H: Handlers=kbd event12
B: PROP=0
B: EV=100013
B: KEY=14afc336 284284d00000000 0 480058000 219040000801 9e96c000000000 90020000000ffc
B: MSC=10

I: Bus=0003 Vendor=2304 Product=0237 Version=0100
N: Name="IR-receiver inside an USB DVB receiver"
P: Phys=usb-0000:00:14.0-1.2/ir0
S: Sysfs=/devices/pci0000:00/0000:00:14.0/usb1/1-1/1-1.2/rc/rc2/input13
U: Uniq=
H: Handlers=kbd event13
B: PROP=0
B: EV=100013
B: KEY=14afc336 284284d00000000 0 480058000 219040000801 9e96c000000000 90020000000ffc
B: MSC=10

I: Bus=0003 Vendor=2304 Product=0237 Version=0100
N: Name="IR-receiver inside an USB DVB receiver"
P: Phys=usb-0000:00:14.0-1.3/ir0
S: Sysfs=/devices/pci0000:00/0000:00:14.0/usb1/1-1/1-1.3/rc/rc3/input14
U: Uniq=
H: Handlers=kbd event14
B: PROP=0
B: EV=100013
B: KEY=14afc336 284284d00000000 0 480058000 219040000801 9e96c000000000 90020000000ffc
B: MSC=10

Till monday I will not able to test your suggestion of restarting lirc, I am out of my city. I will tell you then.

Thanks and regards
Javier B.