2.1 Reading data

We first read the data using the original behaviour readMSData function by setting the mode argument to "inMemory" to generates an in-memory representation of the MS2-level raw data and measure the time needed for this operation.

system.time(inmem <- readMSData(f, msLevel = 2,
                                mode = "inMemory",
                                centroided = TRUE))

##    user  system elapsed 
##  10.765   0.152  11.377

Next, we use the readMSData function to generate an on-disk representation of the same data by setting mode = "onDisk".

system.time(ondisk <- readMSData(f, msLevel = 2,
                                  mode = "onDisk",
                                  centroided = TRUE))

##    user  system elapsed 
##   2.753   0.102   2.965

Creating the on-disk experiment is considerable faster and scales to much bigger, multi-file data, both in terms of object creation time, but also in terms of object size (see next section). We must of course make sure that these two datasets are equivalent:

all.equal(inmem, ondisk)

## [1] TRUE

2.2 Data size

To compare the size occupied in memory of these two objects, we are going to use the object_size function from the pryr package, which accounts for the data (the spectra) in the assayData environment (as opposed to the object.size function from the utils package).

library("pryr")
object_size(inmem)

## 2.77 MB

object_size(ondisk)

## 217 kB

The difference is explained by the fact that for ondisk, the spectra are not created and stored in memory; they are access on disk when needed, such as for example for plotting:

plot(inmem[[200]], full = TRUE)
plot(ondisk[[200]], full = TRUE)

Figure 1: Plotting in-memory and on-disk spectra

2.3 Accessing spectra

The drawback of the on-disk representation is when the spectrum data has to actually be accessed. To compare access time, we are going to use the microbenchmark and repeat access 10 times to compare access to all 451 and a single spectrum in-memory (i.e. pre-loaded and constructed) and on-disk (i.e. on-the-fly access).

library("microbenchmark")
mb <- microbenchmark(spectra(inmem),
                     inmem[[200]],
                     spectra(ondisk),
                     ondisk[[200]],
                     times = 10)
mb

## Unit: microseconds
##             expr         min          lq         mean       median
##   spectra(inmem)     235.721     381.532     368.4412     390.8295
##     inmem[[200]]      76.731      86.083     119.3737     106.1630
##  spectra(ondisk) 1002361.378 1013302.639 1032463.4459 1023066.1465
##    ondisk[[200]]  587209.215  595725.327  603568.5058  599492.8885
##           uq         max neval cld
##      409.058     431.862    10 a  
##      128.978     253.085    10 a  
##  1042863.767 1077662.481    10   c
##   613429.731  631568.568    10  b

While it takes order or magnitudes more time to access the data on-the-fly rather than a pre-generated spectrum, accessing all spectra is only marginally slower than accessing all spectra, as most of the time is spent preparing the file for access, which is done only once.

On-disk access performance will depend on the read throughput of the disk. A comparison of the data import of the above file from an internal solid state drive and from an USB3 connected hard disk showed only small differences for the onDisk mode (1.07 vs 1.36 seconds), while no difference were observed for accessing individual or all spectra. Thus, for this particular setup, performance was about the same for SSD and HDD. This might however not apply to setting in which data import is performed in parallel from multiple files.

Data access does not prohibit interactive usage, such as plotting, for example, as it is about 1/2 seconds, which is an operation that is relatively rare, compared to subsetting and filtering, which are faster for on-disk data:

i <- sample(length(inmem), 100)
system.time(inmem[i])

##    user  system elapsed 
##   0.244   0.001   0.257

system.time(ondisk[i])

##    user  system elapsed 
##   0.037   0.000   0.043

Operations on the spectra data, such as peak picking, smoothing, cleaning, … are cleverly cached and only applied when the data is accessed, to minimise file access overhead. Finally, specific operations such as for example quantitation (see next section) are optimised for speed.

2.4 MS2 quantitation

Below, we perform TMT 6-plex reporter ions quantitation on the first 100 spectra and verify that the results are identical (ignoring feature names).

system.time(eim <- quantify(inmem[1:100], reporters = TMT6,
                            method = "max"))

##    user  system elapsed 
##   7.729   3.012   3.323

system.time(eod <- quantify(ondisk[1:100], reporters = TMT6,
                            method = "max"))

##    user  system elapsed 
##   0.487   0.042   0.533

all.equal(eim, eod, check.attributes = FALSE)

## [1] TRUE

3.1 MS levels

On-disk support multiple MS levels in one object, while in-memory only supports a single level. While support for multiple MS levels could be added to the in-memory back-end, memory constrains make this pretty-much useless and will most likely never happen.

3.2 Serialisation

In-memory objects can be save()ed and load()ed, while on-disk can’t. As a workaround, the latter can be coerced to in-memory instances with as(, "MSnExp"). We would need mzML write support in mzR to be able to implement serialisation for on-disk data.

3.3 Data processing

Whenever possible, accessing and processing on-disk data is delayed (lazy processing). These operations are stored in a processing queue until the spectra are effectively instantiated.

3.4 Validity

The on-disk validObject method doesn’t verify the validity on the spectra (as there aren’t any to check). The validateOnDiskMSnExp function, on the other hand, instantiates all spectra and checks their validity (in addition to calling validObject).